64 lines
4.3 KiB
Markdown
64 lines
4.3 KiB
Markdown
# Lixonet Enterprise Edition (LIXONET 3)
|
|
|
|
This is the semi-official, testing Lixonet EE repository.
|
|
|
|
Custom configurations should be supplied in a `lixonet.conf` file in the `name=value` format, such as your subnet. Additionally, a tinc keypair is also be required.
|
|
|
|
**Generating keypairs for tinc (`tinc.key`)**:
|
|
|
|
Source: https://www.tinc-vpn.org/documentation/Generating-keypairs.html
|
|
|
|
Run: `tincd -n lixonet -K`
|
|
|
|
# Configuration options
|
|
|
|
All options are supplied in the `name=value` format on individual lines, i.e. `name=test_name_lixo`
|
|
|
|
## Required options
|
|
|
|
You **MUST** specify these options, or Lixonet will not work.
|
|
|
|
#### Network options
|
|
|
|
* `name` - The global neighbor name. Tinc and Bird use this to identify a peer in the network, and to exclude your own pre-packed config automagically from Tinc and BIRD dialing out so you don't connect to yourself over and over again.
|
|
* `address` - The *router* address to use. This is your Lixonet routing layer address: 172.xxx.0.xxx
|
|
* `network_address` - The *network* address to use. This is your Lixonet routing layer address: 172.xxx.0.0 (especially take note of the last two 0's: `0.0` -- it _MUST_ end with zeros corresponding to the network size)
|
|
* `asn` - The BGP ASN to use. We usually follow the format `4206969XXX` where _XXX_ is the last octet of your `address`, zero-padded (i.e. 008 or 212)
|
|
|
|
#### Tinc options
|
|
* `tinc_bind_address` - OPTIONAL: The address that Tinc should bind to to _listen_ for incoming WAN-sided connections (i.e. 10.0.0.1). This is _not_ the tunnel IP.
|
|
* `tinc_connect_to` - OPTIONAL: A comma-separated list of well-known/pre-defined hosts to connect to (i.e. `denco_mane_lixo`). If not supplied, this is automatically set to all core routers that aren't yourself (`name`).
|
|
|
|
## Non-required options:
|
|
|
|
#### Network options
|
|
* `global_prefix`: global network prefix: defaults to `16`.
|
|
* `router_prefix`: router network prefix: defaults to `24`. If you change this you _SHOULD_ change `netmask` too.
|
|
* `netmask`: router netmask: defaults to `255.255.255.0` (`/24`); _SHOULD_ be the bitmask that corresponds to the `router_prefix`
|
|
|
|
#### BGP
|
|
|
|
For options we expose here, for information see: https://bird.network.cz/?get_doc&v=20&f=bird-6.html#ss6.3
|
|
|
|
* `bgp_path_metric`: Enable comparison of path lengths when deciding which BGP route is the best one (`0` or `1`): defaults to `1`
|
|
* `bgp_aigp`: BGP AIGP state (`enable`, `disable`, or `originate`): defaults to `originate` (see BIRD documentation)
|
|
* `bgp_rpki_retry`: If RPKI cache data cannot be obtained, the time period in seconds between a failed query the next attempt. Defaults to `90`.
|
|
* `bgp_rpki_refresh`: How long to wait in seconds before attempting to poll RPKI cache data after the last successful poll. Defaults to `900`.
|
|
* `bgp_rpki_expire`: How long to keep any records locally cached before they are deleted. Defaults to `172800` (2 days).
|
|
* `bgp_rpki_known_hosts`: The file path for the SSH key `known_hosts` file to use when validating remote RPKI hosts. Defaults to `/etc/bird/rpki/known_hosts` (provided by Lixonet; don't change this unless you need to!).
|
|
|
|
# Setup
|
|
|
|
Prerequisites:
|
|
1. `docker` and `docker-compose` (Alpine: community repository; https://docs.genesys.com/Documentation/System/8.5.x/DDG/InstallationofDockeronAlpineLinux), `git`, and `curl` are installed (Alpine: `apk add`). You may also want to make docker run at boot: `rc-update add docker boot`.
|
|
2. `eth0` is the **LAN** or **WAN** interface supporting external routing, DNS, etc., and is the **birdged** interface to a router that will statically route the entire desired network subnet (i.e. x.x.0.0/16) through it
|
|
4. `tun` and `tap` are in `/etc/modules` to load at boot (https://www.cyberciti.biz/faq/linux-how-to-load-a-kernel-module-automatically-at-boot-time/) and the system has been rebooted afterwards.
|
|
5. `sigil` is installed (`curl -L "https://github.com/gliderlabs/sigil/releases/download/v0.5.0/sigil_0.5.0_$(uname -sm|tr ' ' '_').tgz" | tar -zxC /usr/local/bin`)
|
|
6. IPv4 forwarding is on: `sysctl -w net.ipv4.ip_forward=1` and `iptables -P FORWARD ACCEPT` are run (and persisted) to allow IP forwarding.
|
|
Install:
|
|
1. Clone this repository: `git clone`
|
|
2. `mkdir /etc/lixonet/`
|
|
3. Fill out `/etc/lixonet/lixonet.conf` (see: **Configuration options**)
|
|
4. Supply `/etc/lixonet/tinc.key`
|
|
5. Run `chmod +x build.sh && ./build.sh` to deploy the stack on Docker.
|